Marble tiles do get cracked at times. Like from any hit by heavy items or constant pressure by heavy furniture. However, you don’t have to live with broken or cracked tiles. You must replace the broken floor tile with a new one. However, the toughness of the repairing process can vary. Like if the floor is installed with a bed of mortar. And also a thin set of adhesives.
Thus, the process of replacing tiles is pretty much the same. There are many options in marble available for floors. So, the best Calacatta Gold marble does not just look attractive but super durable and timeless. Here are the simple steps to replace the old and broken tiles with a new ones. Let’s have a look at it.
List Of Content:
- Material required
- Tools / Equipment Required
- Steps
- Clearing the Grout
- Piece Up The Tile
- Take Out The Tile
- Smoothen The Underlayment
- Seal Down The New Tile
- Apply Mortar Under It
- Level The Floor
- Seal The Floor
- Where To Buy Affordable Calacatta Gold Marble?
- Conclusion
Material required:
- Leveling compound
- Replacement marble tiles
- Plastic tile spacers
- Tile grout
- Grout sealer
- Marble sealant
- Thin-set mortar or tile-setting mortar
Tools / Equipment Required:
- Eye protection
- Medium-grit sandpaper
- Carbide-tipped grout saw
- Work gloves
- Masonry chisel
- Foam brush
- Hammer
- Notched trowel
- Needle nose pliers
- Rubber mallet
- Wet cloth
- Old screwdriver
- Grout float
- Scrap piece
Steps:
Below are some simple steps you need to follow such as;
Clearing the Grout:
First, use a carbide-tipped grout saw or any electric dermal machine. So, remove the grout from the joints of broken tiles with care. Make sure to not chip off the edges of adjacent tiles. Thus, grind the grout well to easily remove the broken tile.
Piece Up The Tile:
Once you’re done removing the grout. It’s time for breaking the tile into small pieces. So, you can easily remove them. Simply, place a nail set in the center and strike it with a hammer. Keep stroking until a crack occurs at the center. This can be strenuous but worthy.
Take Out The Tile:
Now it’s time to remove the broken tile pieces. So, simply insert a masonry chisel tip into a crack. And tap it lightly at one end. Keep doing until it stuck deep down in the tile. Thus, make sure to maintain an accurate angle with a chisel. Don’t let the chisel damage the underlayment. Now hopefully you can pull out the tile pieces away from cement or plywood board.
Smoothen The Underlayment:
Scrape away the tiles, adhesives, and mortar as much as you can. Simply use a chisel or knife. So, the effort needed to scrape away the material depends on the type of material used. Like in thin-set adhesive it is easy to pull them off. Then to cement or plywood underlayment.
Also Read: https://nesttile.com/collections/tundra-gray-marble
Moreover, in older payments, cement-like mortar is used. And it also needs enough energy to smooth the underlayment. Thus, simply use medium-grade sandpaper to sand down the surface. To make it as smooth and flat as possible
Seal Down The New Tile:
Marble is quite porous in nature. So, it is vulnerable to stains and spots. And it gets stained quickly if installed carelessly. Thus, use a foam brush to apply a light coat of marble surface sealant solution. It will create blind protection over the tile. This will not only protect the tile surface but no adhesive or mortar will be able to stain it.
Apply Mortar Under It:
Now mix up a small amount of tile mortar or thin-set adhesive. Then apply it on the backside of the replacement tile by using a ¼-inch notched trowel. Thus, press down the tile firmly by hand. To make it stick to mortar. You can also insert some plastic tile spacers around the edges. So, the grout lines stay steady with the original grout joints.
Level The Floor:
Place a scrap straight over the floor and slightly tap it. Thus, tap the floor with a rubber mallet to make the new tile align with neighboring tiles. Make sure to tap gently to avoid any damage or cracks.
Seal The Floor:
As grout on the floor is dried now. You can simply apply a grout joint with sealant. So, simply apply it with a foam brush. Now as a finishing touch you can seal down the whole floor. In addition, you need to seal the marble floor every 6-12 months. Sealing the floor fully can make the new tile blend with the old tiles.
Where To Buy An Affordable Calacatta Gold Marble?
If you are looking to buy marble and other floor tiles material. So, you must not hustle and perplex. The Nesttiles in the USA is the ultimate destination for all your floor tile shopping. Thus, style your home floor with an iconic calacatta gold marble. It will not only look unique and gorgeous. But it is affordable and highly durable too.
Conclusion:
In conclusion, it is quite real to have broken or damaged tile or marble floors. So, you don’t need to worry. You can simply replace the damaged tile. Here is this descriptive guide above. There are some really easy steps to replace the broken marble tile with a new one. It might need your energy. But will save you money.
Like simply clear the grout, pull up the tile. Then simply level the floor and place the new tile over there. Lastly, fix it by sealing the whole floor and grout the joints. Moreover, always choose durable and affordable marble types. Like calacatta gold marble which will look so appealing in your home.